Guide to Flash New Firmware Samsung GALAXY J2 With ODIN v3.11.1

Flash Stock Firmware Samsung GALAXY J2. This Guide will show you how to Flash / Install Firmware Samsung GALAXY J2 Using ODIN v3.11.1. There are some versions, of this device, J200H with no LTE (South Africa, Kazakhstan), J200GU (Philippines, Malaysia, Thailand), J200Y (New Zealand, Taiwan); J200G (India, Indonesia), J200F (UAE, Turkey). Upgrade your Samsung GALAXY J2 firmware using Samsung’s own utilities OTA (Over-the-air) or Samsung Kies only. Use this guide only if you understand or sure 96% about risks involved in flashing your Samsung GALAXY J2 device.

This device is released on 2015, September. Samsung GALAXY J2 is the smartphone with 4,7 Inchi Super AMOLED capacitive touchscreen, 16M colors, work on Android OS, v5.1.1 (Lollipop), Powered by  Quad-core 1.3 GHz Cortex-A7 CPU, Exynos 3475 Quad Chipset, Mali-T720 GPU, combined with 1 GB of RAM and 5 MP of  Main camera and 2 MP on secondary camera. 

Pre Requisite.

Below is the following things you must do before flashing your Android Samsung Smartphone device.

1. Make sure your Samsung GALAXY J2 is fully charged. or minimum has 93% of battery capacity. It will avoid the flashing process failure.
2. Flashing process will delete or wipe all data stored in internal memory. So, don't forget to backup all data before flashing device.
3. Make sure you have installed a latest of the Samsung driver, that support with your device, If you don't have, you can download here 
4. Original USB cable driver for your Samsung GALAXY J2.
5. Download Odin V3.11.1, Here. 
6. Firmware Download. (use one of the 3 methods below to download Samsung Firmware)
• One. Download Official firmware file for the model number of your device, download it from - SamMobile, or you can visit samsung-updates.com/
• Two. Guide How to Download Official Samsung Firmware From SamMobile. Here 
• Three. Firmware Samsung GALAXY J2, you must Log In to download firmware via this link below.

Guide To Flash Samsung GALAXY J2 

1. You must download all necessary file.(Samsung USB driver and Odin)
2. Then, install all driver to your computer or PC.
3. Extract Odin V3.11.1. file on the destination folder.
4. Switch Off your Samsung GALAXY J2 to start flashing process.
5. Then, run Odin3 v3.11.1 by right click on Odin.exe and select Run as Administrator.

   

   Flash Stock Firmware On Samsung GALAXY J2

6. When program is running, now you can click AP, and navigate to the *.tar or *.tar.md5 firmware file. 

   

   Flash Stock Firmware On Samsung GALAXY J2

7. Now your firmware file has been inserted in Odin3 

   

   Flash Stock Firmware On Samsung GALAXY J2

8. Then, Enter download mode your Samsung GALAXY J2. See this guide how to do it. 
9. On this mode, now connect your Samsung GALAXY J2 to your PC / laptop using a USB cable. 
10. After your phone connected, you will see a message appear that show your device added and there is info on the ID: COM at top left corner. Keep in mind for this COM vary depending on the PC / Laptop. Just Ignore all, in this picture you will see that your device is detected on (COM 5)

    

    Port Com Samsung GALAXY J2

11. Make sure re-partition is NOT ticked
12. When everything already you can click Start Button. at the bottom left corner
13. Just wait for the process to run about 2-5 minutes, and make sure there is no interference in this process. 
14. When complete it will display a notification PASS and your smartphone Samsung GALAXY J2 will automatically restart.
15. Wait your device to boot up, it will take a while.
16. When your Samsung GALAXY J2 is ready to use, now check your firmware version. See this guide how to check it. 
17. Finish.